Opiniões sobre Megger MFT-X1 EVSE Test Kit with EVCA210

{{widget type="Magento\Cms\Block\Widget\Block" template="widget/static_block/default.phtml" block_id="161" type_name="CMS Static Block"}}Megger MFT-X1 EVSE Test Kit The Megger MFT-X1 EVSE Test Kit comes complete with a Megger MFT X-1 Multifunction Tester and a Megger EVCA210-UK Electrical Vehicle Charger Adaptor. The MFT-X1 is designed to be used on all single or 3 phase domestic, commercial and industrial installations. Capable of performing a wide range of tests including high resolution 0.001Ω loop testing, automatic volt drop measurement, stabilised installation test voltage, configurable RCD and EV test sequence tests. The EVCA210-UK adaptor is an easy to use electrical connector designed to throughly test Mode 3 AC Electric Vehicle charge points.Megger MFT-X1 Multifunction Tester The MFT-X1 is suitable for both EV charge point installation testing with RCD Type B or RDC protected charge points. Used alongside the Megger EVCA adaptor, The MFT-X1 can test and maintain all known EV chargers. The Megger MFT-X1 features a high contrast 480 x 272 colour display (with monochrome mode) and an enhanced colour-coded test selection rotary dial for ease of use in all lighting conditions. The MFT-X1 is deigned for the electrical testing of single and 3-phase installations. Using the patented confidence meter True loop measurements can be taken and is fully compatible with CertSuite for easy certificate generation and reporting. Incorporating a stabilised insulation test voltage to ensure the output voltage is accurate within +/-3% +2 digits. The MFT-X1 provides a highly accurate test voltage without the risk of over voltage damage to circuits and components. The Megger MFT-X1 can be powered with either the included Megger Li-ION battery pack or using standard NiMH or Alkaline batteries. The rechargeable Li-ION battery can be swapped with the AA carrier module, providing a fast and flexible battery solution. The IP54 housing and CAT IV 300V safety rated providing users with a rugged and water proof carry case for a full days work even in challenging environments. Megger EVCA210-UK Electric Vehicle Charge Point Adaptor The Megger EVCA210-UK Electric Vehicle Charge Point Adaptor is built to simulate the connection between an electrical vehicle and a charging point that is being tested. The EVCA210 adaptor using its intuitive interface can determine dangerous voltages that are present on the PE. Both Type 1 and Type 2 plugs are supplied with unit with Type 1 plugs for charging points with fixed cables and vehicles connectors and Type 2 plugs used for fixed cables with vehicle connectors air charging points featuring panel mounted socket outlets. This instrument boasts an input voltage of up to 250V in a single phase system, up to 430V in a three phase system and input frequency of 50/60Hz. The EVCA210 incorporates front mounted mains sockets and 4mm connection ports (L1, L2, L3, N and PE) for performing measurements on live conductors whilst the two additional CP signal thermals so a technician can measure CP signal signal via an oscilloscope. The EVCA210 is IP54 rated offering protection from dust ingress and encased in a soft carry case. The CAT II 300V device conducts testing in accordance with IEC/EN 61851-1 and IEC/HD 60364-7-722 regulations. The unit is also compliant with Low Voltage Directive LVD 2014/35 and in line with EC/EN 61010-1:2010 and IEC/EN 61010-2-030:2010 safety standards. EVX100 vs EVCA210 Charge Point Adaptors The EVX100 and the EVCA210 are both available for use with the Megger MFT-X1, with both offering different features that enhance the testing experience. The table below highlights the key abilities and differences of the two adaptors.   EVX100 EVCA210 Purpose Automated EV charger testing accessory for MFT-X1 tester Standalone adaptor for EV charging-point testing Input Voltage 230V AC nominal max 253V AC, 400V AC nominal max 440 V AC Up to 250V (single phase system), up to 430V (three phase system) Input Frequency 50/60Hz 50/60Hz CP States A1, A2, B1, B2, C1, C2, E, F A, B, C, D Environmental Rating IP54 IP54 RCD Testing Automated RCD tests with reset function Manual RCD tests, including RDC-DD fault conditions Power Source Rechargeable lithium-ion battery, USB-C charging Powered directly through the connected EVSE Standards Compliance IEC 61851 (through MFT-X1 functions) IEC 61851 Control Fully automated through MFT-X1 interface, with manual available Manual CP/PP state adjustments via dials/buttons PP Resistance Simulation Integrated with MFT-X1 for automatic testing Adjustable using rotary switch for manual configuration Megger Certsuite™ Electrical Certification Software Compatible (Optional Extra) The Megger MFT-X1 Multifunction Tester is compatible with the Megger Certsuite™ Electrical Certification Software - Single User, 12 Month Licence is a cloud based system compatible with both Android and iOS smart devices as well as a number of browsers (Chrome, Microsoft Edge, Firefox, Safari and Opera) for use on laptops or desktop PC's. Certsuite™ offers users a software licence that is fully compliant and maintained to the latest amendments of BS7671. Offering. secure software package for printing and storing professional certificates and reports, users are able to use the software both online and offline. When used online the Certsuite™ software, data and test measurements are automatically synced to the cloud. When work is conducted offline, the data and test results can be added and uploaded once the internet connection is restored. Site and customer information can be preloaded to help reduce down time, colleagues can access and upload data from the same job at the same time.{{widget type="Magento\Cms\Block\Widget\Block" template="widget/static_block/default.phtml" block_id="179" type_name="CMS Static Block"}}Key Features Designed for the electrical testing of single and 3-phase installations Brand new features including full colour screen, RCD configurator and EV charge point testing TrueLoop measurement using patented confidence meter Fully compatible with CertSuite for easy certificate generation and reporting Never be without power with our quick-remove battery pack and rechargeable battery option Testing adaptor for Mode 3 Electric Vehicle charge points (AC) EVSE tester capable of testing single and three phase EV charging points Single phase system - Input voltage up to 250V Three phase system - Input voltage up to 430V Input frequency of 50/60Hz Simulates the connection an Electric Vehicle to charging point PE pre-test function Button for CP Error “E” & PE Error (Earth Fault) simulation Rotary dial provides PP State or CP state simulation Suitable for an array of appliances with Type 2 & Type 1 charging plugs included 4mm front mounted connection ports (L1, L2, L3, N and PE) Two 4mm ports for connection to an oscilloscope Lightweight & compact design IP54 and CAT II 300V rated In accordance with regulations - IEC/EN 61851-1 and IEC/HD 60364-7-722 In line with directive - LVD 2014/35 Compliant with safety standards - EC/EN 61010-1:2010 and IEC/EN 61010-2-030:2010